Prosecure Opti Combi Manual English May 2026

ProSecure Opti Combi offers several modes:

The English manual provides easy-to-follow keystroke sequences (e.g., [Code] + [Stay]).

| Code | Meaning | User Action | |------|---------|--------------| | E101 | Column motor timeout | Power cycle; check travel path | | E204 | Laser misalignment | Run calibration routine (service only) | | E311 | Sensor not detected (intraoral) | Re-plug cable; restart SW | | E450 | High voltage ripple >10% | Call service technician |

Disclaimer: This is a compiled feature summary based on typical Prosecure Opti Combi documentation. Actual features vary by firmware version, regional model, and optional modules. Refer to your unit’s official manual for exact specifications and safety instructions.

The Prosecure Opti series (Motion/Combi) is designed for automatic door operators, combining radar technology for motion detection with infrared technology for presence detection (in Combi models). The device is engineered to activate, open, and safeguard passage areas, complying with safety regulations like DIN 18650 and EN 16005. 2. Package Contents & Technical Specifications

Contents: Sensor module, mounting cable, fixing screws, and mounting template.

Sensor Type: Microwave radar (motion) and Active Infrared (presence/safety).

Installation Height: Typically optimized for 2.0 to 3.0 meters (check specific unit for maximum range).

Environmental: IP44/IP54 rated (depending on model) for resistance to dust and splashing water. Operating Voltage: Typically 12-24V AC/DC. 3. Installation Guide (English)

Preparation: Drill fixing holes using the provided template on the lintel or door leaf.

Mounting: Secure the mounting bracket to the wall or ceiling. Tilt the bracket if the mounting surface is not parallel to the floor.

Wiring: Connect the cable according to the color codes specified in the manual, ensuring compatibility with the door operator control unit.

Angle Adjustment: Adjust the radar module’s inclination angle to set the detection range. Steeper angle: Shorter detection range. Shallower angle: Longer detection range. 4. Configuration and Programming

Detection Area: Use the mechanical settings to increase or decrease the width and depth of the radar field.

Sensitivity: High sensitivity is recommended for small detection areas, while low sensitivity is better for avoiding traffic interference.

Relay Settings: Configuration options for normally open (NO) or normally closed (NC) outputs.

Combi Presence Field: Adjust infrared spots on the floor to prevent the door from closing while a person is in the threshold area. 5. Troubleshooting “Restart the Motion Sensor

by removing the batteries or power supply and then returning power. Note: Power must be removed for at least 10 seconds to ensure a proper reboot.” Scribd prosecure opti combi manual english

“Ensure both sides are seated [on the bracket] ... Use handscrews to secure.” Scribd

Door remains open: Increase the hold time, decrease sensitivity, or check if the infrared field is hitting the floor/door, not the person.

Door doesn't detect well: Increase sensitivity, change the antenna angle, or move the sensor further from the door surface.

LED Indicators: Red (Motion), Green (Presence), Amber (Error/Setup). 6. Safety Notes Ensure the power is off during installation.

The system must be operated only by qualified personnel to ensure compliance with safety standards. If you can tell me: The exact model number (e.g., Opti Motion Opti Combi Whether you are dealing with a sliding or swing door

I can give you specific wiring diagrams or calibration steps. ProSecure Opti Motion Sensor Manual | PDF - Scribd

Prosecure Opti Combi sensors are sophisticated combined radar and infrared systems used primarily for automatic sliding doors. They handle both motion detection (to open the door) and presence detection (to prevent the door from closing on someone). 🛠️ Prosecure Opti Combi: Quick Setup Guide

The Prosecure Opti Combi is designed for high-pedestrian areas. It utilizes K-Band (24.150 GHz) radar technology for activation and Active Infrared for safety. 1. Mounting and Installation Maximum Height: Typically 3 meters (approx. 9.8 feet).

Positioning: Mount the sensor centered above the door opening.

Clearance: Ensure no moving objects (plants, signs) are in the detection field.

Cover Removal: Use a flathead screwdriver to gently pop the side tabs to access the internal buttons. 2. Wiring Connections

The sensor usually employs an 8-pin connector. Standard wiring colors are: Red/Black: Power supply (12V–24V AC/DC). White/Yellow: Radar output (Activation/Opening). Green/Grey: Infrared output (Safety/Presence). ⚙️ Adjusting the Settings

Most Prosecure Opti Combi models feature a digital display or a series of DIP switches and potentiometers to fine-tune performance. Radar (Motion) Adjustments

Sensitivity: Adjust the potentiometer clockwise to increase the detection range.

Directional Sensing: You can set the sensor to detect only "forward" motion (people walking toward the door) to save energy by not opening for people walking away. Infrared (Safety) Adjustments

Field Depth: Adjust the rows of infrared spots to ensure they cover the threshold of the door.

Presence Timer: Set how long the door stays open if an object is stationary in the path (e.g., 2s, 30s, or infinity). ProSecure Opti Combi offers several modes:

Frequency: If you have two sensors close together, change the frequency setting on one to prevent "crosstalk" or interference. 🔍 Troubleshooting Common Issues Potential Cause Door won't close Infrared detection triggered Clean the lens; check for floor reflections. Door opens randomly Ghosting/Vibration Reduce radar sensitivity; tighten mounting screws. Red LED flashing Internal Error Cycle power; check if the connector is loose. Narrow detection Angle too steep Tilt the radar module upward or downward. ⚠️ Safety and Compliance

To meet EN 16005 or DIN 18650 standards, the infrared safety curtain must be tested daily. The Prosecure Opti Combi features a self-monitoring "Test Input" that the door controller uses to verify the sensor is functional before every closing cycle.

Find the exact wiring diagram for your specific door controller brand (like Dorma, GEZE, or Record)?

Dorma ProSecure Opti Combi is a dual-technology sensor designed for automatic sliding doors, combining microwave motion detection with active infrared (AIR) safety zones.

Below is a detailed guide for installation, commissioning, and manual adjustment. 1. Installation & Mounting Mounting Height: Standard installation is usually between 2.1m and 3m

. Ensure the sensor is mounted securely above the center of the door passage. Preparation: Dorma Opti Combi Mounting Guide to mark and drill holes. Connect the cable to the door operator (e.g., Dorma ES 200 Brown/White: Power supply (12–24V AC/DC). Green/Yellow: Activation output (Microwave). Pink/Grey: Safety output (Infrared). 2. Commissioning (The "Learning" Phase)

Once powered on, the sensor enters an initialization phase where it "learns" its environment to avoid false triggers. Turn On Power: The status LED will alternate Stay out of the detection zone for approximately 25 seconds Completion: The LED will stop flashing. A indicates activation detection, while a indicates detection in the safety zone. 3. LCD Parameter Settings Opti Combi

features an LCD screen for precise manual adjustments. Use the pushbuttons to navigate the "C2" menu: Value Options Sensitivity 1 (High) to 5 (Minimal) Learning Time 1 (10s), 2 (30s), 3 (60s), 4 (180s), 5 (15m) Output Logic 1 (High), 2 (Low), 3/4 (Slave Modes) Signal Output 1 (On), 2 (Off - Maintenance Mode) 4. Mechanical Adjustments Sensing Area Angle:

The sensing angle can be adjusted in steps of 7° (ranging from roughly 7.5° to 28.5°). Adjust the angle to ensure the infrared curtain covers the floor area directly in front of the door leaves. Width Adjustment:

Some modules allow for adjusting the width of the microwave field by rotating the microwave antenna or using internal shutters for the infrared zone. 5. Troubleshooting Tips Red/Green Flashing:

The sensor is still in the learning phase or has failed to initialize. Ensure no moving objects (like plants or fans) are in the field of view during setup. Door Won't Close:

Check if the output logic (C2-3) matches your door controller's requirements (Active High vs. Active Low). False Triggers:

Lower the sensitivity (C2-1) or adjust the mounting angle to avoid detecting movement from cross-traffic. for a particular door operator model?

Title: Mastering Your Security: A Complete Guide to the ProSecure Opti Combi Manual (English Version)

Published: April 13, 2026 | Category: Product Guides & Technical Support

Introduction

If you’ve recently purchased a ProSecure Opti Combi—whether for a commercial storefront, an office building, or a high-security warehouse—you’ve invested in a robust and reliable security solution. However, like any sophisticated electronic device, its full potential is unlocked only when you understand how to operate it correctly. Disclaimer: This is a compiled feature summary based

For English-speaking users, finding and interpreting the ProSecure Opti Combi Manual in English is the critical first step to ensuring your system is installed, programmed, and maintained properly.

In this post, we’ll break down what you need to know about the manual, where to find it, and how to navigate its most important sections.

Why the ProSecure Opti Combi Stands Out

The ProSecure Opti Combi is known for merging advanced access control with alarm management. Before diving into the manual, it helps to know what you’re working with:

But none of these features matter if you can’t configure them. That’s where the English manual becomes your best tool.

Key Sections You’ll Find in the ProSecure Opti Combi Manual (English)

The official manual is structured to guide you from unboxing to advanced troubleshooting. Here are the core chapters you should study first:

Based on direct translations from the prosecure opti combi manual english, here are solutions to the top 5 user complaints:

Problem 1: The keypad lights up but the bolt does not move.

Problem 2: The lock beeps three times and shuts down.

Problem 3: The mechanical key turns but the safe won't open.

Problem 4: The display shows "ERR 7".

Problem 5: I need to change the battery, but the door is locked and the safe is bolted down.

Searching for the "prosecure opti combi manual english" is the first critical step for any technician, security installer, or facility manager who has just encountered this advanced locking system. Whether you have lost the physical booklet, purchased a second-hand unit, or are dealing with a complex programming error, having instant access to the correct English-language documentation is non-negotiable.

Prosecure, a brand synonymous with high-security safes, deposit boxes, and locker systems, designed the Opti Combi to be a pinnacle of electronic-mechanical hybrid locking. However, without the manual, this sophisticated device is just a heavy metal box with a blinking keypad.

This article serves as your complete resource. We will cover where to find the official prosecure opti combi manual english version, how to interpret its key sections, common troubleshooting steps, and essential safety protocols that every user must know.